Whirlpool fridges are a well-liked selection for a lot of households, however even the very best home equipment want a bit upkeep every so often. Probably the most necessary upkeep duties is altering the water filter. A unclean water filter can result in quite a few issues, together with diminished water move, bad-tasting water, and even ice buildup.
Luckily, altering the water filter in a Whirlpool fridge is a comparatively simple process. On this article, we’ll give you step-by-step directions on how one can do it. We’ll additionally provide you with some recommendations on how to decide on the correct water filter in your fridge. Moreover, we are going to give you some troubleshooting suggestions in case you run into any issues.
Probably the most necessary issues to bear in mind when altering the water filter in your Whirlpool fridge is to decide on the correct filter. There are a selection of various water filters out there in the marketplace, so it is necessary to pick one that’s suitable along with your fridge mannequin. You’ll be able to often discover this data in your fridge’s guide. After getting the correct filter, you may comply with the steps under to alter it.
Figuring out the Filter’s Location
Figuring out the filter’s location in a Whirlpool fridge is essential for a seamless filter alternative course of. Here is an in depth information to information you thru:
Step 1: Examine the Fridge’s Entrance Panel
In most Whirlpool fridge fashions, the water filter is conveniently positioned behind the grille on the entrance panel. To find it, search for a small, rectangular panel often close to the highest or backside of the door. Gently press the sides of the grille to launch it, exposing the filter housing.
Step 2: Look at the Grille on the Inside of the Fridge
When you do not discover the filter behind the entrance panel grille, it might be positioned contained in the fridge. Examine the again wall of the fridge compartment for a small, spherical filter housing. It could be tucked away in a nook or behind a detachable panel.
Step 3: Consult with the Proprietor’s Guide
When you’re nonetheless uncertain in regards to the filter’s location, seek the advice of your Whirlpool fridge’s proprietor’s guide. It is going to present particular directions and illustrations that can assist you pinpoint the filter’s precise placement.
| Mannequin Sort | Filter Location |
|---|---|
| High-Freezer | Behind the grille on the entrance panel, close to the highest |
| Backside-Freezer | Contained in the fridge, on the again wall |
| French Door | Behind the grille on the entrance panel, close to the underside |
| Aspect-by-Aspect | Contained in the fridge, behind a detachable panel |
Eradicating the Previous Filter
To take away the previous water filter, comply with these detailed steps:
1. Find the Filter Housing: The water filter is usually positioned within the fridge’s higher right-hand nook, behind the grille. It is enclosed in a filter housing which will have a twist or push-to-remove mechanism.
2. Shut Off Water Provide: It is essential to show off the water provide to the fridge earlier than dealing with the filter. Find the water valve, often behind or underneath the fridge, and switch it clockwise to the “off” place.
3. Depressurize the System: Open the water dispenser on the fridge door to launch any remaining water strain within the system. Maintain it open till the water move stops fully.
4. Take away the Filter Housing:
- Push-to-Take away Housing: Press the push-button on the filter housing and concurrently pull it straight in direction of you to launch it.
- Twist-Off Housing: Grip the housing and twist it counterclockwise roughly 1 / 4 flip. It ought to loosen and pull out simply.
- Detachable Clip or Bracket: Some fashions have a clip or bracket that holds the housing in place. Find the discharge mechanism and depress or unhook it to unlock the housing.
5. Pull Out the Previous Filter: As soon as the housing is eliminated, seize the previous filter by its deal with and gently pull it straight out of the housing.
Putting in the New Filter
After getting positioned the previous filter, it is time to set up the brand new one. Listed below are the steps:
- Take away the previous filter. Grip the filter firmly and twist it counterclockwise about 1/4 flip. Pull the filter straight down and out of the housing, being cautious to not spill any water.
- Clear the filter housing. Wipe the within of the housing with a clear material to take away any particles or previous filter residue.
- Examine the brand new filter. Take away the brand new filter from its packaging and examine it for any injury. If the filter is broken, don’t set up it. Contact Whirlpool customer support for help.
- Lubricate the O-rings. Apply a small quantity of food-grade lubricant to the 2 O-rings on the brand new filter. It will assist to make sure a cosy match and stop leaks.
- Insert the brand new filter. Align the brand new filter with the housing and insert it into place. Flip the filter clockwise about 1/4 flip to lock it in place. Tighten the filter by hand; don’t use instruments.
- Run water via the filter. After putting in the brand new filter, run chilly water via the dispenser for a number of minutes to purge any air from the system. The water could also be discolored at first, however that is regular and will clear up after a couple of minutes.
Troubleshooting
When you encounter any issues putting in the brand new filter, please consult with the next troubleshooting suggestions:
* The filter will not come out. If the previous filter is caught, you may attempt utilizing a pair of pliers to grip it and twist it free. You may as well attempt tapping the filter calmly with a hammer to loosen it.
* The filter leaks. If the brand new filter leaks, be sure that the O-rings are correctly lubricated and that the filter is tightened securely. If the leak persists, contact Whirlpool customer support for help.
* The water is discolored. After putting in the brand new filter, run chilly water via the dispenser for a number of minutes to purge any air from the system. The water could also be discolored at first, however that is regular and will clear up after a couple of minutes. If the water continues to be discolored after a number of minutes, contact Whirlpool customer support for help.
Resetting the Filter Indicator
After getting changed the water filter in your Whirlpool fridge, you might want to reset the filter indicator. It will let the fridge know {that a} new filter has been put in and that it ought to begin counting all the way down to the following filter change.
To reset the filter indicator, comply with these steps:
1. Discover the “Filter Reset” button on the fridge’s management panel. It’s often positioned close to the water dispenser.
2. Press and maintain the “Filter Reset” button for 3-5 seconds.
3. Launch the button and the filter indicator will reset.
Detailed Directions for Resetting the Filter Indicator
| Step | Description |
|---|---|
| 1 | Find the “Filter Reset” button in your fridge’s management panel. Consult with your person guide for the precise location if wanted. |
| 2 | Press and maintain the “Filter Reset” button firmly for 3-5 seconds. Don’t launch the button prematurely. |
| 3 | As soon as the 3-5 seconds have handed, launch the button. The filter indicator ought to now be reset. |
If the filter indicator doesn’t reset after following these steps, you could must contact Whirlpool customer support for help.
Find the Water Filter
The water filter in Whirlpool fridges is usually positioned contained in the fridge compartment, behind the grille or kickplate on the backside entrance. Find the filter and take away the grille or kickplate to entry it.
Take away the Previous Filter
After getting positioned the water filter, grasp it firmly and twist it counterclockwise to take away it from the housing. Watch out to not spill any water which may be left within the filter.
Set up the New Filter
Take the brand new water filter and insert it into the housing. Align the filter with the alignment marks and twist it clockwise to tighten it. Be certain that it’s securely in place.
Reset the Filter Indicator
Most Whirlpool fridges have a filter indicator mild that may activate when the filter must be changed. After getting put in the brand new filter, reset the indicator mild by urgent and holding the “Filter Reset” button for just a few seconds.
Troubleshooting Frequent Points
The Water Filter is Leaking
When you discover water leaking from the water filter, it might be brought on by:
- A unfastened filter housing
- A cracked or broken filter
- A defective O-ring
The Water Circulate is Sluggish
If the water move from the fridge is sluggish, it might be brought on by:
- A clogged water filter
- A kinked or frozen water line
- A defective water valve
The Water Filter Indicator Mild is Not Resetting
If the filter indicator mild will not be resetting after you could have put in a brand new filter, it might be brought on by:
- A defective reset button
- A broken wire harness
- An issue with the management board
Beneficial Frequency of Filter Modifications
To make sure optimum water filtration efficiency and preserve the well being of your fridge, it is suggested to exchange the water filter commonly. The beneficial frequency of filter modifications varies relying on the mannequin of your Whirlpool fridge, nevertheless it usually ranges from each 6 to 12 months. For particular tips, seek the advice of your fridge’s person guide or contact Whirlpool buyer assist.
8. Learn how to Change Water Filter
1. Open the fridge door and find the water filter housing. It’s often positioned within the higher proper or left-hand nook of the fridge compartment.
2. Shut the water consumption valve to cease water move. Usually, it is a quarter-turn valve positioned behind the fridge.
3. Push the discharge button on the water filter housing and rotate it counterclockwise to take away the previous filter.
4. Moist each ends of the brand new filter in water and take away the protecting cap.
5. Insert the brand new filter into the housing and rotate it clockwise till it clicks into place.
6. Open the water consumption valve and run water via the filter for about 5 minutes to flush out any air or impurities.
7. Reset the water filter indicator mild, in case your mannequin has one.
Changing a Water Filter in a Whirlpool Fridge
9. Putting in the New Filter:
– Retrieve the brand new filter from its packaging and take away any protecting cap or plastic wrap.
– Find the filter housing unit usually discovered on the fridge’s ceiling or again inside wall.
– Align the brand new filter with the housing and insert it firmly till it clicks into place.
– Twist the filter clockwise to lock it securely. (For some fashions, you could must carry the filter into the housing after which twist it.)
– Run chilly water via the dispenser for five minutes to flush out any air or particles.
Advantages of Frequently Altering the Filter
Changing the water filter in your Whirlpool fridge commonly gives a number of advantages:
–
Improved Water Style: A clear filter removes impurities, enhancing the style and odor of your ingesting water.
–
Decreased Contamination: Filters lure contaminants like chlorine, sediment, and micro organism, guaranteeing the protection of your ingesting water.
–
Safety of Home equipment: By eradicating impurities, filters shield your fridge’s ice maker and water dispenser from injury.
–
Prolonged Equipment Life: Common filter modifications lengthen the lifespan of your fridge by lowering pressure on its inside parts.
–
Price-Effectiveness: Changing filters commonly is less expensive than buying bottled water and prevents expensive repairs on account of contaminated water.
Learn how to Change Water Filter in Whirlpool Fridge
Sustaining the purity of your ingesting water is important in your well being and well-being. A clear water filter ensures that your water is free from contaminants, resembling chlorine, sediment, and different impurities. Altering your Whirlpool fridge’s water filter is a straightforward process that may be accomplished in a matter of minutes.
To alter your water filter, comply with these steps:
- Find the water filter compartment. The placement of the filter compartment might differ relying on the mannequin of your Whirlpool fridge. In most fashions, the compartment is positioned behind the top-right grille on the entrance of the fridge.
- Flip off the water provide to the fridge. This shut-off valve is usually positioned behind the fridge, close to the water line connection.
- Take away the previous water filter. To take away the previous filter, merely pull it straight down from the filter compartment.
- Insert the brand new water filter. Align the brand new filter with the filter compartment and push it in place till it clicks.
- Activate the water provide to the fridge.
- Run water via the dispenser for a couple of minutes. It will purge any air from the system and be certain that the water is flowing correctly.
You will need to change your Whirlpool fridge’s water filter each six months, or extra usually when you’ve got arduous water. Altering the filter commonly will assist to make sure that your ingesting water is clear and secure.
Individuals Additionally Ask about Learn how to Change Water Filter in Whirlpool Fridge
How do I do know when to alter my Whirlpool fridge’s water filter?
Whirlpool recommends altering the water filter each six months. Nonetheless, you could want to alter the filter extra usually when you’ve got arduous water or if the water coming out of your fridge has an odd style or odor.
What sort of water filter do I want for my Whirlpool fridge?
Whirlpool fridges use Whirlpool-brand water filters. The kind of filter you want will depend upon the mannequin of your fridge. Yow will discover the proper filter mannequin quantity on the proprietor’s guide in your fridge.
Can I exploit a unique model of water filter in my Whirlpool fridge?
Whilst you can technically use a unique model of water filter in your Whirlpool fridge, it’s not beneficial. Whirlpool filters are designed to suit completely in your fridge and to work with the fridge’s water filtration system. Utilizing a unique model of filter might not present the identical stage of filtration or might not match correctly.
