A mix of exact measurements, cautious planning, and knowledgeable craftsmanship is required to finish the set up of a tub drain and lure, as they’re essential plumbing elements that enable water to circulation easily from the bathtub and into the drainage system. This course of, though seemingly advanced, could be manageable with the fitting instruments, supplies, and, in fact, complete directions. On this information, we are going to take you step-by-step by the set up course of, guaranteeing your bathtub features optimally and drains effectively.
Earlier than delving into the set up, it’s crucial to assemble all the required supplies. These sometimes embody a tub drain, a P-trap, a slip-joint nut, a rubber washer, plumbers putty, and a wrench. Moreover, having a bucket, a screwdriver, a putty knife, and a degree could make the method smoother. With these instruments and supplies at your disposal, you may confidently embark on the set up journey.
Step one entails making ready the tub drain. Start by making use of a beneficiant quantity of plumbers putty across the base of the tub drain. Subsequent, fastidiously insert the drain into the drain gap and safe it with the slip-joint nut, guaranteeing it’s hand-tightened. Make the most of the wrench to additional tighten the nut by a few quarter flip, avoiding overtightening. Now, it is time to set up the P-trap. Join one finish of the P-trap to the drainpipe utilizing the slip-joint nut and tighten it by hand. Connect the opposite finish of the P-trap to the tub drain, once more utilizing the slip-joint nut and tightening it by hand. Lastly, use the wrench to totally tighten each connections, however keep away from extreme drive.
Supplies You may Want
When embarking on a tub drain and lure set up, it is essential to assemble the required supplies to make sure a profitable and environment friendly course of. Here is a complete record of things you may require:
Important Instruments for the Activity
| Device | Objective |
|---|---|
| Adjustable wrench | Tightening and loosening drain meeting elements |
| Pliers | Holding and manipulating small fittings |
| Screwdriver (flathead or Phillips) | Eradicating and tightening screws |
| Putty knife | Making use of and smoothing plumber’s putty |
| Tape measure | Measuring the gap for chopping the drain pipe |
| Flashlight | Illuminating darkish areas for higher visibility |
| Security glasses | Defending eyes from particles and chemical compounds |
Important Supplies for the Set up
| Materials | Objective |
|---|---|
| New bathtub drain | Changing the previous or broken drain |
| Tubular lure | Putting in a brand new lure to stop clogs |
| Plumber’s putty | Making a watertight seal across the drain |
| Drain cleansing answer | Dissolving any current clogs or obstructions |
| Plastic or brass drain becoming | Connecting the drain to the lure |
| Drain strainer | Catching hair and particles to stop clogs |
Putting in the Bathtub Drain Gasket
Place the rubber drain gasket across the base of the drain physique. The gasket ought to match snugly across the base, guaranteeing a watertight seal when the drain is put in.
Putting in the Bathtub Drain Physique
Place the drain physique over the drain opening and apply a bead of plumber’s putty to the underside of the flange. Press the drain physique into place, rotating it barely to evenly distribute the putty.
Putting in the Bathtub Drain Tailpiece
- Threaded Tailpiece: Screw the threaded tailpiece into the drain physique, tightening it securely. Use Teflon tape on the threads for a leak-free seal.
- Slip-Joint Tailpiece: Insert the slip-joint tailpiece into the drain physique and tighten the nuts on each side till the connection is comfortable. Be certain that the tailpiece is positioned accurately for correct drainage.
| Execs | Issues | |
|---|---|---|
|
Threaded Tailpiece |
Straightforward to put in |
Requires exact alignment |
|
Slip-Joint Tailpiece |
Versatile match for various drain openings |
Could also be much less safe than threaded tailpieces |
Attaching the Overflow Drain
Attaching the overflow drain is an important step in putting in a tub drain and lure. It ensures that extra water can escape the bathtub and prevents overflows. Here is an in depth information on how you can connect the overflow drain:
-
Collect your supplies: You have to the overflow drain plate, overflow drain tube, and plumbers tape.
-
Tighten the overflow plate: Place the overflow drain plate over the overflow gap on the tub. Use a wrench to tighten the plate onto the bathtub, guaranteeing a safe match.
-
Apply plumbers tape to the overflow tube: Take the overflow drain tube and wrap the tip with a number of layers of plumbers tape. This can assist create a watertight seal when connecting the tube.
-
Join the overflow tube: Insert the taped finish of the overflow drain tube into the overflow drain gap on the overflow plate. Fastidiously push the tube into place and tighten it by hand to create a seal. You possibly can additional safe the reference to a wrench, however keep away from overtightening.
| Tip | Description |
|---|---|
| Use Plumbers Putty | For a safer seal, apply a skinny layer of plumbers putty across the base of the overflow plate earlier than tightening it. |
| Test for Leaks | After attaching the overflow drain, fill the tub with water and test for leaks across the connection. Tighten the tube or plate if needed. |
Connecting the Drain Meeting to the Lure
1. Start by making use of a skinny layer of plumber’s putty to the bottom of the tailpiece washer.
2. Place the washer over the tailpiece and tighten the slip nut onto the lure inlet by hand.
3. Utilizing a basin wrench or adjustable wrench, gently tighten the slip nut an extra quarter to half flip.
4. Keep away from overtightening the slip nut, as this may crack the lure or injury the putty seal.
5. Insert the opposite finish of the tailpiece into the drain meeting and tighten the slip nut onto the drain meeting by hand.
6. Once more, utilizing a basin wrench or adjustable wrench, gently tighten the slip nut an extra quarter to half flip.
7. Double-check the tightness of all connections and make sure that there aren’t any leaks.
8. **Putting in the Stopper and Overflow Meeting (If Relevant)**
In case your bathtub has a stopper and overflow meeting, comply with these steps to finish the set up:
| Step | Description |
|---|---|
| a | Find the overflow tube and insert it into the overflow gap on the tub. |
| b | Place the stopper washer over the tip of the overflow tube and tighten the stopper nut onto the washer. |
| c | Insert the stopper physique into the drain meeting and tighten the stopper screw by hand. |
| d | Use a screwdriver to tighten the stopper screw an extra quarter flip. |
| e | Take a look at the stopper meeting by opening and shutting the stopper to make sure correct operation. |
Ending Touches
As soon as the drain and lure are in place, you may end the set up by:
1. Making use of Caulk
Apply a bead of caulk across the drain flange and the place the overflow plate meets the bathtub. Clean the caulk together with your finger or a caulk software.
2. Putting in the Drain Stopper
Insert the drain stopper into the drain and tighten the bolt.
3. Attaching the Overflow Plate
Place the overflow plate over the overflow gap and screw it into place.
4. Changing the Tub Spout
In the event you eliminated the bathtub spout, reinstall it now.
5. Connecting the Drain to the P-Lure
Slide the drain over the P-trap inlet and tighten the slip nut.
6. Connecting the P-Lure to the Drain Outlet
Slide the P-trap over the drain outlet and tighten the slip nut.
7. Putting in the Drain Rod
Insert the drain rod into the overflow and safe it with a screw.
8. Trimming the Drain Pipe
If needed, trim the drain pipe to the specified size.
9. Flushing the Drain
Run water by the drain to test for leaks.
10. Last Inspection
Examine all connections to make sure they’re correctly seated and tight. Test for any leaks and make needed changes.
| Element | Objective |
|---|---|
| Caulk | Seal the drain flange and overflow plate to the bathtub |
| Drain Stopper | Plug the drain to stop water from escaping |
| Overflow Plate | Stop water from overflowing the bathtub |
| Tub Spout | Ship water to the bathtub |
| P-Lure | Stop sewer gases from coming into the bathtub |
| Drain Rod | Join the overflow to the drain |
| Drain Pipe | Carry water from the bathtub to the drain |
How To Set up A Bathtub Drain And Lure
Step 1: Take away the previous drain meeting.
Utilizing a pair of pliers, loosen the retaining nut on the underside of the drain. As soon as the nut is free, you may pull the drain meeting up and off the drain pipe.
Step 2: Clear the drain pipe.
Utilizing a rag or a sponge, clear the within of the drain pipe to take away any particles or residue. This can assist to make sure that the brand new drain meeting will match correctly.
Step 3: Set up the brand new drain meeting.
Place the brand new drain meeting over the drain pipe and tighten the retaining nut. Guarantee that the drain meeting is tight sufficient to stop leaks, however not so tight that you just injury the drain pipe.
Step 4: Set up the lure.
The lure is a U-shaped pipe that connects the drain meeting to the waste line. Place the lure over the drain meeting and tighten the slip nuts on each ends of the lure. Guarantee that the lure is tight sufficient to stop leaks, however not so tight that you just injury the lure.
Step 5: Take a look at the drain meeting.
Activate the water and let it run for a couple of minutes. Test for any leaks across the drain meeting or the lure. In the event you see any leaks, tighten the retaining nut or the slip nuts as wanted.
Folks Additionally Ask About How To Set up A Bathtub Drain And Lure
How do you exchange a tub drain stopper?
To interchange a tub drain stopper, you have to to take away the previous stopper and set up a brand new one. To take away the previous stopper, you have to to make use of a pair of pliers to loosen the retaining nut on the underside of the stopper. As soon as the nut is free, you may pull the stopper up and off the drain pipe. To put in the brand new stopper, you have to to position the stopper over the drain pipe and tighten the retaining nut. Guarantee that the stopper is tight sufficient to stop leaks, however not so tight that you just injury the drain pipe.
How do you repair a leaky bathtub drain?
To repair a leaky bathtub drain, you have to to determine the supply of the leak and restore it. The commonest causes of tub drain leaks are free connections, broken washers, and cracked drain pipes.
How do you clear a tub drain?
To scrub a tub drain, you have to to take away the drain stopper and pour a drain cleaner down the drain. Let the drain cleaner sit for the period of time specified on the product label. As soon as the drain cleaner has sat for the required period of time, flush the drain with sizzling water. It’s possible you’ll have to repeat this course of a number of occasions to utterly clear the drain.
