Putting in jigsaw blades on DeWalt 20-volt jigsaws is usually a breeze! Here is a step-by-step information that can assist you get it completed shortly and effectively. Start by guaranteeing that your jigsaw is off and the battery is disconnected. It is essential to work on a cooled-down jigsaw to stop any burns.
Find the blade ejection lever on the entrance of the noticed. It’s usually a small, spring-loaded lever. Push the lever away from you and concurrently pull down the blade clamp. This may mean you can clear the trail for the brand new blade. Subsequent, align the brand new blade’s tooth going through downwards and insert it into the blade clamp. Fastidiously push the blade up till it’s securely held in place. Launch the blade clamp by pushing it in the direction of you and lock the blade in place by participating the blade ejection lever again into its authentic place. Make sure the blade is firmly seated by gently pulling on it.
Lastly, reconnect the battery and activate the jigsaw. Take a look at the blade by making a number of cuts on a scrap piece of wooden. If the blade cuts easily with none wobbling or vibration, you’ve efficiently put in the blade. Keep in mind, it is indispensable to put on gloves and security glasses all through the method on your safety.
Disassembling the Jigsaw
Earlier than you may insert a brand new blade into your DeWalt 20V jigsaw, you should first disassemble the device. Observe these steps to take action safely and effectively:
1. Unplug the Jigsaw
Initially, it’s essential to unplug the jigsaw from the facility supply. This security precaution prevents unintentional activation whereas disassembling the device. Find the facility twine and disconnect it on the plug.
As soon as the jigsaw is unplugged, you may proceed to the following steps.
2. Take away the Shoe Insert
The shoe insert is a small, detachable piece situated on the bottom of the jigsaw. To take away it, merely grasp the insert together with your fingers or a pair of pliers and pull it straight out. This may expose the blade clamp mechanism beneath.
3. Open the Blade Clamp
With the shoe insert eliminated, you will notice a steel blade clamp. To open the clamp, find the lever or knob on the aspect of the jigsaw and rotate it counterclockwise. This may loosen the clamp and mean you can insert or take away the jigsaw blade safely.
4. Take away the Outdated Blade
As soon as the blade clamp is open, you may take away the previous blade. Grip the blade firmly with one hand and gently pull it straight up out of the clamp. If the blade is caught, chances are you’ll want to make use of a pair of pliers or a screwdriver to assist pry it unfastened.
Inserting the New Blade
As soon as you’ve got chosen the suitable blade on your mission, it is time to insert it into the jigsaw. Here is an in depth step-by-step information:
Step 1: Take away the Base Plate
Loosen the screws holding the bottom plate in place utilizing an Allen key or wrench. Fastidiously elevate off the bottom plate to reveal the blade clamp.
Step 2: Open the Blade Clamp
Find the lever or dial that releases the blade clamp. Press or flip the discharge mechanism to open the clamp and permit the insertion of the brand new blade.
Step 3: Insert the Blade
Align the tooth of the brand new blade with the information slots on the blade clamp. Insert the blade into the clamp guaranteeing that the tooth are going through within the right course. The blade needs to be inserted with the tooth pointing downward for slicing on the upstroke and upward for slicing on the downstroke.
| Slicing Path | Tooth Orientation |
|---|---|
| Upstroke (Slicing on the best way up) | Tooth going through downward |
| Downstroke (Slicing on the best way down) | Tooth going through upward |
Tip: For those who’re uncertain of the right tooth orientation, seek the advice of your jigsaw’s guide or examine the producer’s web site for particular steering.
Step 4: Shut the Blade Clamp
As soon as the blade is inserted, press or flip the discharge mechanism once more to shut the blade clamp. Make sure that the blade is securely held in place with none wobble.
Step 5: Reattach the Base Plate
Place the bottom plate again onto the jigsaw and tighten the screws to safe it. Your new jigsaw blade is now put in and prepared to be used.
Securing the Blade
4. Tightening the Blade: A Complete Information
As soon as the blade is seated accurately, it is essential to tighten it securely. Use the offered wrench or key to carry the retaining bolt nonetheless whilst you flip the nut clockwise utilizing the opposite hand. Guarantee you’ve a agency grip and apply sufficient power to snugly fasten the blade, however keep away from overtightening as it might warp or injury the blade. To make sure correct tightness, use a torque wrench set to the producer’s beneficial torque specification. Nonetheless, for those who’re working and not using a torque wrench, goal for a comfortable match that permits the blade to maneuver freely with out extreme play.
| Tip | Clarification |
|---|---|
| Safe the blade firmly, however do not overtighten | Overtightening can warp or injury the blade |
| Use a torque wrench for exact tightening | Ensures correct tightness with out damaging the blade |
| Goal for a comfortable match with out extreme play | Permits the blade to maneuver freely throughout slicing |
Adjusting Blade Pressure
As soon as you’ve got inserted the blade, you may want to regulate the blade stress to make sure it is held securely. Most DeWalt jigsaws have a tool-less blade stress lever or knob that means that you can simply regulate the strain with out the necessity for a hex key or different instruments. Here is how one can regulate the blade stress:
- Establish the blade stress adjustment lever or knob in your particular DeWalt jigsaw mannequin.
- Maintain the lever or knob and switch it counterclockwise to loosen the blade stress.
- Insert the blade into the jigsaw and tighten the lever or knob clockwise till the blade is held firmly in place.
- Take a look at the blade stress by gently pulling on the blade. It ought to really feel cosy however not overly tight.
- If the blade strikes too simply or rattles, tighten the strain lever or knob additional. If the blade is just too tight, it might bind or break throughout operation, so loosen the strain barely.
Suggestions for Adjusting Blade Pressure
- Totally different blades could require completely different stress settings. Thinner blades typically require much less stress than thicker blades.
- All the time examine the blade stress earlier than every use to make sure it is safe and correctly adjusted.
- Keep away from overtightening the blade stress, as this may injury the blade or the jigsaw mechanism.
Security Precautions
1. Put on Security Gear: All the time put on eye safety, gloves, and a mud masks when working with energy instruments.
2. Unplug Energy Instrument: Earlier than performing any upkeep or changes, make sure that the jigsaw is unplugged from the facility supply.
3. Examine Blade: Verify the blade for any injury or put on earlier than set up. Don’t use a broken blade.
4. Preserve Away from Blade: Preserve your palms and fingers away from the blade space whereas the jigsaw is operating.
5. Securely Clamp Workpiece: Safe the workpiece firmly earlier than beginning to minimize. This may forestall the fabric from shifting throughout the slicing course of.
6. Keep away from Kickbacks: Keep a agency grip on the jigsaw and use each palms to regulate the device. Keep away from slicing into supplies which are too thick or exhausting, as this may trigger kickbacks.
7. Use Right Blade: Select the right blade for the fabric you’re slicing. Incorrect blade choice can result in ineffective slicing and potential hazards.
8. Observe Producers’ Directions: Check with the producer’s directions for particular security tips and upkeep procedures.
9. Further Precautions for 20 Volt DeWalt Jigsaws:
- Take away Battery Earlier than Altering Blade: All the time take away the battery from the jigsaw earlier than altering the blade.
- Find Blade Clamp Lever: Establish the blade clamp lever on the jigsaw, normally situated close to the blade housing.
- Pull Up Clamp Lever: Pull up the blade clamp lever to launch the blade.
- Take away Outdated Blade: Grip the previous blade firmly with gloved palms and pull it straight out of the blade holder.
- Insert New Blade: Align the brand new blade with the blade holder and insert it securely.
- Safe Blade: Push down on the blade clamp lever to safe the brand new blade in place.
- Examine Blade Set up: Make sure that the blade is correctly put in and securely fixed earlier than persevering with.
Putting in Dewalt Jigsaw Blades 20 Volt
Step 1: Collect Supplies
You have to a Dewalt jigsaw, a Dewalt 20V jigsaw blade, and a Phillips head screwdriver.
Step 2: Put together the Jigsaw
Take away the battery from the jigsaw and insert the jigsaw blade into the blade clamp.
Step 3: Tighten the Blade Clamp
Use the Phillips head screwdriver to tighten the blade clamp screw till the blade is securely held.
Step 4: Reattach the Battery
Reattach the battery to the jigsaw.
Step 5: Take a look at the Blade
Activate the jigsaw and make a number of take a look at cuts to make sure the blade is put in accurately and slicing easily.
Troubleshooting Suggestions
1. The blade is just not slicing straight
Verify if the blade is put in accurately and if the blade clamp is tight. If the issue persists, attempt a brand new blade.
2. The blade is vibrating excessively
Verify if the blade is bent or broken. Whether it is, exchange the blade. Additionally, examine if the jigsaw is balanced correctly and if the blade clamp is tight.
3. The blade is just not slicing via the fabric
Verify if the blade is sharp and if the jigsaw is ready to the right pace for the fabric being minimize. If the issue persists, attempt a unique blade.
4. The jigsaw is overheating
Cease utilizing the jigsaw and let it calm down. Verify if the blade is caught or if the jigsaw is clogged with sawdust. Clear the jigsaw and check out utilizing a brand new blade.
5. The jigsaw is making unusual noises
Cease utilizing the jigsaw and examine if there are any unfastened elements or broken elements. For those who discover any issues, contact a certified restore technician.
6. The jigsaw is just not beginning
Verify if the battery is charged and if the jigsaw is correctly plugged into an outlet. If the issue persists, attempt a unique battery or contact a certified restore technician.
7. The jigsaw is just not responding to the set off
Verify if the set off is caught or broken. Whether it is, contact a certified restore technician.
8. The jigsaw is smoking
Cease utilizing the jigsaw instantly and unplug it from the outlet. Contact a certified restore technician.
9. The jigsaw is leaking oil
Cease utilizing the jigsaw and call a certified restore technician.
10. The jigsaw is just not coated by the guarantee
If the jigsaw is just not coated by the guarantee, you may contact a certified restore technician. They will diagnose the issue and supply a value estimate for the repairs.
How To Set up Dewalt Jigsaw Blades 20 Volt
Putting in Dewalt jigsaw blades on a 20-volt jigsaw is a straightforward course of that may be accomplished in a couple of minutes. Listed below are the steps you should comply with:
- Flip off the jigsaw and unplug it from the facility supply. That is essential for security causes.
- Open the blade clamp. To do that, push the lever or button that’s situated on the aspect of the jigsaw. The blade clamp will open, permitting you to take away the previous blade.
- Take away the previous blade. Grip the previous blade together with your fingers and pull it straight out of the blade clamp.
- Insert the brand new blade. Align the brand new blade with the blade clamp and insert it into the clamp. Make it possible for the tooth of the blade are going through within the right course.
- Shut the blade clamp. Push the lever or button that you just used to open the blade clamp. The blade clamp will shut, securing the brand new blade in place.
- Plug within the jigsaw and switch it on. Your jigsaw is now prepared to make use of.
Individuals Additionally Ask About How To Set up Dewalt Jigsaw Blades 20 Volt
What’s one of the simplest ways to chop a straight line with a jigsaw?
To chop a straight line with a jigsaw, use a straight edge as a information. Place the straight edge alongside the road you wish to minimize and maintain it firmly in place. Then, begin slicing alongside the road, maintaining the jigsaw in opposition to the straight edge.
What’s one of the simplest ways to chop a curve with a jigsaw?
To chop a curve with a jigsaw, use a freehand method. Begin by slicing alongside the skin fringe of the curve. Then, step by step transfer the jigsaw in the direction of the within fringe of the curve, ensuring to maintain the blade perpendicular to the floor of the fabric.
What’s one of the simplest ways to chop a gap with a jigsaw?
To chop a gap with a jigsaw, first drill a pilot gap within the middle of the opening. Then, insert the jigsaw blade into the pilot gap and begin slicing. Preserve the jigsaw perpendicular to the floor of the fabric and step by step transfer the jigsaw across the circumference of the opening.
