Changing a heating factor in a Samsung dryer can prevent the price of shopping for a brand new dryer or hiring an equipment restore technician. To switch the heating factor, you may first want to assemble the mandatory instruments and supplies, together with a brand new heating factor, screwdriver, and pliers. After you have the mandatory gadgets, comply with these steps to exchange the heating factor in your Samsung dryer.
First, unplug the dryer from the ability outlet and take away the again panel of the dryer. Subsequent, find the heating factor and disconnect the wires which can be connected to it. Then, take away the outdated heating factor from the dryer. To put in the brand new heating factor, merely insert it into the dryer and reconnect the wires. Lastly, exchange the again panel of the dryer and plug it again into the ability outlet. Your Samsung dryer ought to now be working correctly.
In case you are not assured in your means to exchange the heating factor your self, it’s best to contact a professional equipment restore technician. A certified technician will be capable of shortly and safely exchange the heating factor in your Samsung dryer and get it working correctly once more.
Security Precautions
Earlier than embarking on the duty of changing the heating factor in your Samsung dryer, it’s crucial to prioritize your security. Electrical energy and heating components can pose important dangers if correct precautions will not be taken. To make sure a protected and profitable restore, meticulously adhere to the next security measures:
1. Disconnect the Energy Supply
The primary and most important step is to disconnect {the electrical} provide to your dryer. That is a necessary security measure to forestall any unintentional electrical shocks or fires. Find the primary electrical panel in your house and change off the circuit breaker or take away the fuse akin to the dryer. Confirm that the ability has certainly been disconnected by testing the dryer outlet with a voltage tester. Wait a couple of minutes to permit any residual electrical energy within the system to dissipate.
| Ideas for Disconnecting the Energy Supply |
|---|
| – Determine the right circuit breaker or fuse for the dryer. |
| – Swap off the corresponding circuit breaker or take away the fuse. |
| – Use a voltage tester to substantiate that the outlet is now not receiving energy. |
| – Permit enough time for the residual electrical energy to dissipate. |
Collect Vital Instruments and Supplies
Earlier than embarking on the restore, it is essential to assemble the important instruments and supplies. This is an in depth rundown of what you may want:
Supplies:
- New heating factor
- Electrical tape
- Warmth-resistant gloves (non-obligatory)
Instruments:
| Software | Objective |
|---|---|
| Phillips-head screwdriver | Take away the screws securing the entry panels and heating factor |
| Torx screwdriver | Unscrew the bolts holding the heating factor in place (some fashions) |
| Multimeter | Check the continuity of the heating factor (non-obligatory) |
| Pliers (non-obligatory) | Tighten or loosen nuts or bolts |
| Protecting goggles (non-obligatory) | Shield eyes from unfastened particles |
Further Supplies:
Whereas not strictly vital, sure supplies could make the restore course of smoother:
- Flashlight: Illuminate the work space, particularly in dimly lit areas
- Store towels or rags: Clear up any particles or spills
- Digicam: Doc the disassembly course of for simpler reassembly
- Warmth gun (non-obligatory): Soften outdated adhesive or velocity up evaporation of moisture
- Soldering iron (non-obligatory): Restore broken wires or safe new connections
Find and Take away the Rear Panel
Unplug the dryer and transfer it away from the wall.
For security functions, unplug your dryer from the ability outlet earlier than beginning any repairs. It might even be greatest to drag the dryer away from the wall to present your self ample area to work.
Find the screws holding the rear panel in place.
Figuring out the screws that maintain the rear panel of the dryer is essential. These screws are sometimes situated across the perimeter of the panel, and their place might fluctuate barely relying on the dryer mannequin. After you have recognized the screws, proceed to the subsequent step.
Take away the screws and punctiliously raise off the rear panel.
After you have situated the screws, use a screwdriver to take away them. Watch out to not strip the screws or injury the rear panel when eradicating them. After eradicating all of the screws, fastidiously raise the rear panel off the dryer. Notice that the rear panel could also be barely heavy, so make sure to assist it with one hand whereas eradicating the screws with the opposite.
Disconnect Current Heating Aspect
**Step 1: Unplug the Dryer**
Earlier than engaged on the dryer, disconnect it from the ability provide by unplugging it from the wall outlet.
**Step 2: Take away the Again Panel**
Find the screws on the again panel of the dryer and take away them utilizing a screwdriver. Fastidiously raise and take away the again panel to reveal the internal elements.
**Step 3: Disconnect Wires**
Determine the 2 wires linked to the heating factor terminals. Gently pull the wire connectors off the terminals. Make be aware of which wire goes to which terminal for future reference.
**Step 4: Take away the Heating Aspect**
The heating factor is held in place by two screws or bolts. Use a wrench or socket to loosen and take away these fasteners. Fastidiously slide the heating factor out of its housing. Be conscious of sharp edges and keep away from touching the factor along with your naked arms.
| Screw/Bolt Location | Elimination Technique |
|---|---|
| High of the housing | Loosen with a wrench or socket |
| Backside of the housing | Take away with a wrench or socket |
**Step 5: Examine the Heating Aspect**
Visually examine the heating factor for any injury or corrosion. If the factor is broken, it would should be changed earlier than reassembling the dryer.
Take away Outdated Heating Aspect
5. Disconnect the heating factor from the ability provide.
| Kind of Dryer | Steps |
|---|---|
| Gasoline Dryer |
Shut off the fuel provide to the dryer earlier than continuing. |
| Electrical Dryer |
Unplug the dryer from the ability outlet and switch off the circuit breaker or fuse for the dryer circuit |
6. Take away the screws that maintain the heating factor in place.
7. Unclip the wire terminals from the heating factor.
8. Pull the heating factor out of the dryer.
Set up New Heating Aspect
Security Precautions
Earlier than starting any work, unplug your dryer and disconnect the ability supply. Be sure that the machine is cool to the contact.
Eradicating the Outdated Heating Aspect
- Take away the entrance panel of the dryer by unscrewing the screws on the high and pulling it ahead.
- Find the entry panel on the entrance of the dryer’s drum. Take away the screws and pull it open.
- Pull the outdated heating factor unit in direction of you to disconnect the wires.
- Unplug the wires from {the electrical} terminals and take away the outdated heating factor.
Putting in the New Heating Aspect
- Insert the brand new heating factor unit into the opening within the drum.
- Join the wires to {the electrical} terminals. Be sure that the connections are safe.
- Push the heating factor unit again into place and safe it with the screws.
- Reattach the entry panel and the entrance panel of the dryer.
- Plug the dryer again into the ability outlet and switch it on to check the brand new heating factor.
Ideas for Troubleshooting
| Downside | Answer |
|---|---|
| Dryer not heating | Examine the ability provide. Examine the wires and connections to the heating factor. Check the heating factor with a multimeter. |
| Dryer overheating | Unplug the dryer and let it settle down. Clear the lint filter and exhaust vent. Examine the thermostat and temperature sensor. |
Reconnect Electrical Wires
Now it is time to reconnect {the electrical} wires to the heating factor. Make sure to match the wires to the right terminals on the factor. Sometimes, the crimson wire will connect with the left terminal and the white wire will connect with the correct terminal. Nonetheless, consult with your dryer’s particular wiring diagram to substantiate.
Tighten the screws on the terminals securely utilizing a screwdriver. Be sure that the wires are making good contact with the terminals to forestall any unfastened connections that might trigger arcing or different electrical points.
As soon as the wires are linked, tuck them again into the insulation across the heating factor. This can assist to guard the wires from warmth injury and hold the within of the dryer tidy.
Wiring Diagram
For fast reference, here’s a desk with a basic wiring diagram for many Samsung dryers:
| Wire Colour | Terminal |
|---|---|
| Crimson | Left Terminal |
| White | Proper Terminal |
Once more, double-check your dryer’s particular wiring diagram to make sure accuracy earlier than making any connections.
Substitute Rear Panel
Now that the screws are eliminated, raise the rear panel up from the underside and pull it in direction of you to detach it from the dryer. Watch out to not injury any wires or elements as you do that.
As soon as the rear panel is eliminated, you’ll have entry to the heating factor. The heating factor is situated on the backside of the dryer, behind the drum. It’s held in place by two screws.
Step 8: Take away the Heating Aspect’s Wiring
Earlier than eradicating the heating factor, you should disconnect its wiring. The heating factor has two wires linked to it: a black wire and a white wire. Use a pair of pliers to softly pull the wires off of the heating factor’s terminals.
As soon as the wires are disconnected, you possibly can take away the heating factor. Use a screwdriver to take away the 2 screws that maintain the heating factor in place. As soon as the screws are eliminated, the heating factor may be pulled out of the dryer.
| Step 6: Find the Heating Aspect | The heating factor is situated on the backside of the dryer, behind the drum. It’s held in place by two screws. |
| Step 7: Disconnect the Heating Aspect’s Wiring | Earlier than eradicating the heating factor, you should disconnect its wiring. The heating factor has two wires linked to it: a black wire and a white wire. Use a pair of pliers to softly pull the wires off of the heating factor’s terminals. |
| Step 8: Take away the Heating Aspect | As soon as the wires are disconnected, you possibly can take away the heating factor. Use a screwdriver to take away the 2 screws that maintain the heating factor in place. As soon as the screws are eliminated, the heating factor may be pulled out of the dryer. |
As soon as the outdated heating factor is eliminated, you possibly can exchange it with the brand new one. Insert the brand new heating factor into the dryer and safe it with the 2 screws. Make sure to join the wires to the heating factor’s terminals within the appropriate order: black wire to black terminal, white wire to white terminal.
As soon as the brand new heating factor is put in, you possibly can reattach the rear panel to the dryer. Safe the rear panel with the screws that you just eliminated earlier.
Check the Dryer
After you have changed the heating factor, it is very important check the dryer to verify it’s working correctly. Listed here are the steps on how one can check the dryer:
| Step | Motion |
|---|---|
| 1 | Be certain the dryer is plugged into an outlet and that the ability change is turned on. |
| 2 | Open the dryer door and place a moist towel inside. |
| 3 | Shut the dryer door and choose the “Regular” or “Timed Dry” cycle. |
| 4 | Press the “Begin” button to start out the dryer. |
| 5 | Let the dryer run for a couple of minutes to see if the towel will get heat. |
| 6 | If the towel will get heat, then the heating factor is working correctly. |
| 7 | If the towel doesn’t get heat, then there could also be an issue with the heating factor or different elements of the dryer. |
In case you are having issues along with your dryer, it’s best to contact a professional equipment restore technician for help.
Security Precautions Earlier than Beginning:
1. Unplug the dryer from the ability outlet and permit it to chill fully.
2. Put on gloves to guard your arms from sharp edges.
3. Collect all vital instruments and components earlier than beginning.
Checking the Heating Aspect:
1. Take away the again panel of the dryer by unscrewing the screws across the perimeter.
2. Find the heating factor, which is usually an oblong steel field with two wires linked to it.
3. Unplug the wires from the heating factor utilizing needle-nose pliers.
Eradicating the Heating Aspect:
1. Unscrew the nuts holding the heating factor in place.
2. Fastidiously raise the heating factor out of the dryer cupboard.
Putting in the New Heating Aspect:
1. Place the brand new heating factor into the dryer cupboard.
2. Tighten the nuts holding the heating factor in place.
3. Join the wires to the heating factor.
Troubleshooting Ideas
1. If the dryer nonetheless doesn’t warmth, verify the thermal fuse.
2. If the thermal fuse is blown, exchange it.
3. If the heating factor isn’t getting energy, verify the wiring.
4. If the wiring is broken, restore or exchange it.
5. If the dryer continues to be not heating, contact a professional equipment restore technician.
Further Troubleshooting Ideas:
| Doable Trigger | Answer |
|---|---|
| Free belt | Modify or exchange the belt |
| Vent blockage | Clear the dryer vent |
| Defective thermostat | Substitute the thermostat |
| Defective relay | Substitute the relay |
| Defective management board | Substitute the management board |
7. If the dryer is making a loud noise, verify the drum bearings.
8. If the drum bearings are worn, exchange them.
9. If the dryer is shaking excessively, verify the shock absorbers.
10. If the shock absorbers are worn, exchange them.
The right way to Set up a Heating Aspect in a Samsung Dryer
Changing the heating factor in a Samsung dryer is a comparatively easy process that may be accomplished in about an hour. Nonetheless, it is very important take security precautions and comply with the directions fastidiously to keep away from harm or injury to the dryer.
Supplies wanted:
- New heating factor
- Screwdriver
- Wrench
- Security glasses
- Gloves
Directions:
- Unplug the dryer from the ability outlet.
- Placed on security glasses and gloves.
- Take away the again panel of the dryer by unscrewing the screws that maintain it in place.
- Find the heating factor, which is often situated on the backside of the dryer.
- Disconnect the wires from the heating factor.
- Unscrew the bolts that maintain the heating factor in place.
- Carry the heating factor out of the dryer.
- Place the brand new heating factor into the dryer.
- Screw within the bolts to safe the heating factor in place.
- Join the wires to the heating factor.
- Substitute the again panel of the dryer.
- Plug the dryer again into the ability outlet.
