Changing a bathroom paper holder may not rank excessive in your checklist of priorities, however a defective or outdated holder can rapidly change into an annoyance. Whether or not it is continually coming unfastened or just would not match your toilet decor, a brand new rest room paper holder could make a world of distinction. The excellent news is that changing a bathroom paper holder is a comparatively easy DIY undertaking that may be accomplished in only a few minutes. On this article, we’ll stroll you thru the step-by-step means of changing a bathroom paper holder, together with take away the outdated holder and set up the brand new one. By following these directions, you can restore your toilet to its former glory very quickly.
Earlier than you start, it is necessary to assemble the required instruments and supplies. You will want a brand new rest room paper holder, a screwdriver (both a Phillips head or flat head, relying on the kind of screws used in your outdated holder), a drill (in case you’re putting in the brand new holder right into a wall that does not have present holes), and a stage. After you have all the pieces you want, you can begin the substitute course of.
To take away the outdated rest room paper holder, merely unscrew the screws which can be holding it in place. As soon as the screws are eliminated, the holder ought to come off simply. If the holder is especially cussed, it’s possible you’ll want to make use of a pry bar to softly pry it off the wall. As soon as the outdated holder is eliminated, you’ll be able to set up the brand new holder by following the identical steps in reverse. First, maintain the brand new holder as much as the wall and mark the areas of the screw holes. Then, use a drill to create pilot holes for the screws. Subsequent, insert the screws into the pilot holes and tighten them till the holder is safe. Lastly, use a stage to verify the holder is stage, and also you’re all set!
Gathering Supplies and Instruments
Changing a bathroom paper holder is a simple process that sometimes solely requires a couple of primary instruments. Here is an in depth checklist of supplies and instruments you may want for the job:
Supplies:
- New rest room paper holder
- Screws or bolts (if crucial, relying on the holder design)
- Anchors (if crucial, for drywall or different mushy surfaces)
Instruments:
- Screwdriver (Phillips or flathead, relying on the screw kind)
- Drill (if crucial, for putting in anchors)
- Stage (non-obligatory, for exact alignment)
- Measuring tape (non-obligatory)
- Pencil or marker (non-obligatory, for marking holes)
Extra Concerns:
| Materials | Description |
|---|---|
| Anti-rust screws | Beneficial for areas with excessive humidity or publicity to water |
| Ornamental caps or covers | Elective equipment to boost the aesthetics of the holder |
| Stud finder | Elective instrument to find studs within the wall for safe anchoring |
Making ready the Mounting Floor
Earlier than putting in a brand new rest room paper holder, it is important to make sure the mounting floor is sufficiently ready to attain a safe and sturdy set up.
Cleansing the Floor
Begin by totally cleansing the realm the place the bathroom paper holder might be mounted to take away any filth, mud, or particles. Use a moist fabric or sponge with a light cleansing resolution. Enable the floor to dry fully earlier than continuing.
Eradicating Outdated Adhesive
If there may be any remaining adhesive or residue from the earlier rest room paper holder, it should be eliminated. Use a scraping instrument or a industrial adhesive remover to softly scrape away the outdated adhesive. Be cautious to not harm the floor beneath.
Leveling and Marking the Location
As soon as the floor is clear and freed from particles, decide the specified placement for the bathroom paper holder. Use a stage to make sure that the holder might be mounted straight. Mark the placement of the mounting holes with a pencil or a everlasting marker. Check with the producer’s directions for the particular measurements required.
| Step | Motion |
|---|---|
| 1 | Clear the mounting floor |
| 2 | Take away outdated adhesive or residue |
| 3 | Find and mark the mounting factors |
| 4 | Verify for levelness |
Attaching the Bathroom Paper Holder
1. Make Certain the Holder is Mounted at a Handy Peak
Earlier than you mount the bathroom paper holder, ensure it is at a snug top for everybody who might be utilizing it. The best top is often 24-28 inches from the ground to the middle of the roll. Mark the specified location on the wall with a pencil.
2. Align the Mounting Plate
Place the mounting plate over the marked location and stage it utilizing a stage. Use a pencil to mark the screw holes on the wall.
3. Drill Pilot Holes
Utilizing a drill with a masonry bit, drill pilot holes on the marked screw areas. The depth of the holes needs to be barely shorter than the size of the screws you may be utilizing.
4. Insert the Anchor Screws (if wanted)
When you’re mounting the holder into drywall or plaster, insert plastic or steel anchor screws into the pilot holes. These anchors will present additional assist for the screws.
5. Set up the Mounting Plate
Align the mounting plate with the pilot holes. Drive the screws into the holes, both immediately or via the anchor screws. Tighten the screws securely, however not excessively.
| Screw Sort | Description |
|---|---|
| Wooden screws | Used for mounting into wooden surfaces |
| Drywall screws | Used for mounting into drywall or plaster |
| Masonry screws | Used for mounting into concrete or tile |
As soon as the mounting plate is put in, the bathroom paper holder will be hooked up to it by sliding it into place and securing it with the offered screws or bolts.
Security Concerns
Changing a bathroom paper holder could seem easy, but it surely’s important to prioritize security to keep away from potential hazards. Listed below are some necessary security issues to bear in mind:
1. Disconnect the Water Provide: Earlier than beginning any work, flip off the water provide valve situated behind or beneath the bathroom. Flushing the bathroom will assist drain any remaining water from the tank and bowl.
2. Use Correct Instruments: Guarantee you could have the suitable instruments for the job, akin to a screwdriver, wrench, or pliers. Utilizing the proper instruments will decrease the chance of injury or harm.
3. Shield Your Eyes: Put on security glasses to guard your eyes from any particles or flying particles through the course of.
4. Verify for Hidden Hazards: Examine the realm round the bathroom paper holder for any electrical wires, plumbing pipes, or different obstacles that would pose a security hazard.
5. Keep away from Overtightening: When tightening the screws or bolts, be conscious to not overtighten them. Extreme pressure can harm the holder or the encompassing wall materials.
6. Safe the Bracket: Guarantee the bathroom paper holder bracket is securely fixed to the wall to stop it from wobbling or turning into unfastened.
7. Use Waterproof Sealant: For added safety towards moisture harm, apply waterproof sealant across the base of the holder the place it meets the wall.
8. Deal with Porcelain with Care: In case your rest room paper holder is mounted on porcelain tiles, deal with them with care to keep away from chipping or cracking.
9. Examine Frequently: Periodically test the bathroom paper holder for any unfastened screws, cracks, or different indicators of injury. Deal with any points promptly to make sure continued protected and dependable use.
10. Use a Step Stool or Ladder: If the bathroom paper holder is situated at a top, use a step stool or ladder for stability and to stop falls.
How To Change Bathroom Paper Holder
Changing a bathroom paper holder is an easy process that may be accomplished in a couple of minutes. Listed below are the steps concerned:
-
Flip off the water provide to the bathroom.
-
Flush the bathroom to empty the tank.
-
Take away the outdated rest room paper holder by unscrewing the screws that maintain it in place.
-
Set up the brand new rest room paper holder by screwing it into place.
-
Activate the water provide to the bathroom and test for leaks.
Folks Additionally Ask
Can I substitute a bathroom paper holder with out turning off the water?
No, it is best to at all times flip off the water provide to the bathroom earlier than changing the bathroom paper holder. This can stop water from leaking out of the tank whenever you take away the outdated holder.
What kind of screws ought to I take advantage of to put in a bathroom paper holder?
You must use screws which can be the identical dimension as those that held the outdated holder in place. In case you are unsure what dimension screws to make use of, you’ll be able to take the outdated holder to a ironmongery shop and ask for assist.
How usually ought to I substitute my rest room paper holder?
You must substitute your rest room paper holder every time it turns into unfastened or broken. You might also need to substitute it if you wish to replace the look of your toilet.
