Your kitchen faucet is without doubt one of the most-used fixtures in your house. As such, it is clever to turn into accustomed to primary upkeep duties. Must you ever want to switch your kitchen faucet, understanding the way to uninstall it is step one of the method. Whereas knowledgeable plumber can actually maintain this job for you, it’s additionally a reasonably easy DIY undertaking that may be accomplished in a number of easy steps. Maintain studying to discover ways to uninstall kitchen faucet in lower than an hour.
Earlier than starting, you have to to assemble a number of instruments. You have to a pair of adjustable pliers, a screwdriver, a bucket, and some rags. You might also wish to placed on a pair of previous garments or a smock since some water could spill in the course of the elimination course of. After you have your instruments and are prepared to start, step one is to show off the water provide to your kitchen faucet. You possibly can normally discover the shut-off valves below the sink. As soon as the water is turned off, open the tap to launch any remaining water within the line.
Subsequent, you have to to disconnect the water provide strains. To do that, use the adjustable pliers to loosen the nuts that join the water strains to the tap. Watch out to not overtighten the nuts, as this might injury the strains. As soon as the nuts are free, you may disconnect the water strains by hand. Now, you have to to take away the mounting nuts that maintain the tap in place. These nuts are normally positioned beneath the sink. Use the screwdriver to loosen the nuts, however there seemingly is not going to be sufficient clearance to take away them along with your fingers. As a substitute, grip the nuts with the adjustable pliers, and take away them the remainder of the best way. With the mounting nuts eliminated, now you can raise the tap up and out of the sink.
Gathering the Mandatory Instruments
Uninstalling a kitchen faucet requires a number of important instruments to make sure a easy and environment friendly course of. Earlier than you start, collect the next objects:
- **Adjustable wrench:** A big, adjustable wrench is good for loosening and tightening the nuts that safe the tap to the sink and water provide strains.
- **Basin wrench:** This specialised wrench is designed to grip the mounting nuts on the underside of the sink, which are sometimes troublesome to achieve with a daily wrench.
- **Phillips head screwdriver:** You might want a Phillips head screwdriver to take away the deal with screws on some faucet fashions.
- **Flat head screwdriver:** A flat head screwdriver can be utilized to pry open any cussed clamps or clips that could be holding the tap in place.
- **Pliers:** Pliers may be useful for gripping and loosening small nuts or screws that could be troublesome to achieve with different instruments.
- **Bucket:** A bucket is crucial for gathering water which will drain from the tap and water provide strains in the course of the elimination course of.
Extra Instruments for Particular Faucet Sorts
Relying on the kind of faucet you’ve gotten, you might want further instruments. For instance:
| Faucet Kind | Extra Instruments |
|---|---|
| Pull-out faucet | Allen wrench or hex key |
| Touchless faucet | Electrical tape or wire nuts |
Disconnecting the Water Strains
As soon as the tap is disconnected from the sink, you may proceed to disconnect the water strains. On this step, you have to a pair of adjustable wrenches or a basin wrench.
1. Flip off the water provide.
Earlier than beginning, be sure that the water provide to the tap is turned off. You possibly can normally discover the shut-off valves below the sink or within the basement or crawlspace.
2. Detach the provision strains from the tap.
Find the provision strains related to the tap, one for decent water and one for chilly water. Use the adjustable wrench to loosen the nuts that safe the provision strains to the tap. As soon as loosened, you may detach the provision strains by hand.
3. Drain any remaining water.
As soon as the provision strains are disconnected, there could also be some remaining water within the strains or faucet. To empty this water, open the tap and permit it to run till the water stops flowing. Alternatively, you need to use a moist/dry vacuum to suck out the water.
Loosening the Faucet Base
As soon as your water provide is turned off, you may proceed to loosen the tap base. This may be carried out utilizing a wrench or a pair of pliers.
-
Find the 2 nuts which are holding the tap base in place. These nuts are normally positioned on the underside of the tap, simply above the baseplate.
-
Use a wrench or pliers to loosen the nuts. Watch out to not overtighten the nuts, as this will injury the tap.
-
As soon as the nuts are free, it’s best to have the ability to take away the tap base by pulling it straight up.
-
If the tap base is caught, you may attempt utilizing a penetrating oil to loosen it up. Apply the oil to the nuts and let it sit for a couple of minutes earlier than making an attempt to loosen them once more.
| Instruments you have to: |
|---|
| – Adjustable wrench |
| – Penetrating oil (non-compulsory) |
| – Pliers (non-compulsory) |
Eradicating the Faucet Meeting
1. Flip off the water provide to your faucet. That is sometimes carried out by closing the valves beneath the sink.
2. Disconnect the water provide strains. Use a wrench to loosen the nuts that join the provision strains to the tap.
3. Take away the mounting nuts. You have to to find the mounting nuts that safe the tap to the sink. These nuts are sometimes positioned beneath the sink.
4. Pull the tap up and out of the sink. As soon as the mounting nuts have been eliminated, you may pull the tap up and out of the sink.
5. Disconnect the tap deal with. The tap deal with is usually hooked up to the tap physique with a screw or a set screw. Use a screwdriver or a wrench to take away the screw or set screw and detach the deal with.
6. Take away the tap cartridge. The tap cartridge is positioned inside the tap physique. Use a wrench or a screwdriver to take away the cartridge.
7. Clear the tap physique. As soon as the cartridge has been eliminated, you may clear the tap physique with a gentle detergent and water.
8. Reassemble the tap. Reassemble the tap within the reverse order of disassembly.
| Element | Removing |
|---|---|
| Water provide strains | Use a wrench to loosen the nuts that join the provision strains to the tap. |
| Mounting nuts | Find the mounting nuts that safe the tap to the sink and take away them. |
| Faucet deal with | Take away the screw or set screw that secures the deal with to the tap physique. |
| Faucet cartridge | Use a wrench or a screwdriver to take away the cartridge from the tap physique. |
Cleansing the Set up Space
After you have gathered your instruments and supplies, it’s time to begin prepping the set up space. This contains cleansing the tap and sink, in addition to eradicating any previous sealant or caulk. Listed below are some suggestions for cleansing the set up space:
Clear the Faucet
Use a gentle dish cleaning soap and heat water to wash the tap. Be sure you rinse the tap totally and dry it with a clear fabric.
Clear the Sink
Clear the sink utilizing a gentle dish cleaning soap and heat water. Be sure you rinse the sink totally and dry it with a clear fabric.
Take away Outdated Sealant or Caulk
If there’s any previous sealant or caulk across the faucet, take away it utilizing a utility knife or a caulk remover. Watch out to not injury the sink or countertop.
| Extra Ideas for Cleansing the Set up Space |
|---|
| Use a degreaser to take away any grease or grime from the tap and sink. |
| Use a toothbrush to wash any hard-to-reach areas. |
| Rinse the tap and sink totally with clear water. |
| Dry the tap and sink with a clear fabric. |
Putting in the New Faucet Meeting
1. Collect your instruments and supplies. You have to a brand new faucet meeting, a wrench, a screwdriver, and a pair of pliers.
2. Shut off the water provide to the tap. You will see the shut-off valves below the sink.
3. Disconnect the water strains from the previous faucet. Use a wrench to loosen the nuts that maintain the strains in place.
4. Take away the previous faucet. Use a screwdriver to take away the screws that maintain the tap in place. Then, raise the tap out of the sink.
5. Clear the mounting floor. Use a humid fabric to wash the world the place the brand new faucet might be put in.
6. Set up the brand new faucet. Place the brand new faucet within the mounting gap and safe it with the screws.
7. Join the water strains to the brand new faucet. Use a wrench to tighten the nuts that maintain the strains in place. Be sure you tighten the nuts securely, however don’t overtighten them.
| Step | Description |
|---|---|
| 1 | Collect your instruments and supplies. |
| 2 | Shut off the water provide to the tap. |
| 3 | Disconnect the water strains from the previous faucet. |
| 4 | Take away the previous faucet. |
| 5 | Clear the mounting floor. |
| 6 | Set up the brand new faucet. |
| 7 | Join the water strains to the brand new faucet. |
| Step | Motion |
|---|---|
| 1 | Find the water provide valves below the sink. |
| 2 | Flip the handles clockwise to open the water provide. |
| 3 | Examine to make it possible for the water is flowing freely from the tap. |
| 4 | As soon as the water is flowing freely, you may start uninstalling the tap. |
Supplies You will Want
Here’s a record of instruments you have to:
- Wrench
- Pliers
- Basin wrench (non-compulsory)
- Bucket
- Material
- New faucet
Step-by-Step Directions
- Flip off the water provide.
- Place a bucket below the tap to catch any water.
- Disconnect the water provide strains.
- Take away the mounting nuts.
- Pull the tap out of the sink.
- Clear the sink and tap mount.
- Set up the brand new faucet.
- Join the water provide strains.
- Activate the water provide.
- Examine for leaks.
Troubleshooting Frequent Points
1. Faucet is caught.
If the tap is caught, attempt utilizing a wrench to loosen it. If that does not work, you may attempt utilizing a penetrating oil to loosen the threads.
2. Water is leaking from the tap.
If water is leaking from the tap, attempt tightening the mounting nuts. If that does not work, you might want to switch the O-rings or washers.
3. Faucet deal with is free.
If the tap deal with is free, attempt tightening the screws that maintain it in place. If that does not work, you might want to switch the deal with.
4. Faucet just isn’t spraying correctly.
If the tap just isn’t spraying correctly, attempt cleansing the aerator. If that does not work, you might want to switch the aerator.
5. Faucet is making a noise.
If the tap is making a noise, attempt tightening the nuts that maintain it in place. If that does not work, you might have to lubricate the transferring elements.
6. Faucet just isn’t turning off utterly.
If the tap just isn’t turning off utterly, attempt cleansing the seat washer. If that does not work, you might want to switch the seat washer.
7. Faucet is dripping.
If the tap is dripping, attempt tightening the packing nut. If that does not work, you might want to switch the packing nut.
8. Faucet just isn’t working in any respect.
If the tap just isn’t working in any respect, attempt checking {the electrical} provide. If that does not work, you might want to switch the tap.
9. Faucet is leaking from the bottom.
If the tap is leaking from the bottom, attempt tightening the mounting nuts. If that does not work, you might want to switch the O-rings or washers.
10. Faucet just isn’t stage.
If the tap just isn’t stage, attempt adjusting the mounting nuts. If that does not work, you might have to shim the tap.
How To Uninstall Kitchen Faucet
To uninstall a kitchen faucet, you have to the next instruments:
– Adjustable wrench
– Pliers
– Screwdriver
– Bucket
1. Flip off the water provide to the tap. There might be two shut-off valves below the sink, one for the recent water and one for the chilly water. Flip each of those valves clockwise till they’re utterly closed.
2. Open the tap to launch any remaining water stress.
3. Disconnect the water provide strains from the tap. Use an adjustable wrench to loosen the nuts that maintain the strains in place. As soon as the nuts are free, you may pull the strains off of the tap.
4. Take away the mounting nuts. There might be two mounting nuts that maintain the tap in place. Use an adjustable wrench to loosen these nuts. As soon as the nuts are free, you may raise the tap out of the sink.
5. Clear the sink floor. As soon as the tap is eliminated, you may clear the sink floor the place the tap was put in. Use a humid fabric to wipe away any dust or particles.
